Bolt failure at The Mine

Let everyone know about any suspect/dodgy/misplaced bolts to be renewed or avoided.
Post Reply
chrisb
Posts: 9
Joined: Mon Mar 07, 2016 10:04 pm
Real Name: Chris Barker

Bolt failure at The Mine

Post by chrisb » Tue Nov 08, 2016 9:04 pm

DO NOT climb Pink Harmonica in Ashes 19 at The Mine until it has been fixed!

My friend was back-climbing the route to clean it. When she reached the top she left the last quick draw before the chains in place and back-clipped the belayer's end of the rope into it. This is a standard "extra" precaution that I highly recommend when back-climbing a route to clean it. She began to clean at the chains when one of the two bolts snapped off :shock: This would have left her on only one (dodgy) point of safety if she had not left the last in place and back-clipped it. I lowered her down and climbed the route to the side to retrieve our quickdraws. No one was hurt!

We wrote a warning message with chalk on the base of the route to stop people from climbing it. On closer inspection, most of the bolts look to be in a similar state to the one that broke at the top. This route is unsafe to climb until is has been rebolted.

Is this something ARF can do soon?

Cheers!

Chris

User avatar
Justin
Posts: 3597
Joined: Sat Apr 30, 2005 8:31 am
Real Name: Justin Lawson
Location: Montagu
Contact:

Re: Bolt failure at The Mine

Post by Justin » Wed Nov 09, 2016 7:00 am

Thanks for letting us know. Glad nobody got hurt (that is why we have 2x bolts at the top).

Assuming the bolter(s) used the same hardware on the other routes that were opened at the Mine. I would advise staying off all the other routes until the bolts on the other routes can be checked.

http://www.climbing.co.za/wiki/The_Mine
Climb ZA - Administrator
justin@climbing.co.za

Brussel
Posts: 234
Joined: Mon Jan 23, 2006 1:52 pm

Re: Bolt failure at The Mine

Post by Brussel » Wed Nov 09, 2016 7:25 am

in so far as I recall there where several routes (of which pink harmonica is one) that were bolted by Scott Millar at about the same time and probably use the same hardware

mokganjetsi
Posts: 1549
Joined: Fri Dec 15, 2006 12:32 pm
Real Name: Willem Boshoff
Location: Cape Town

Re: Bolt failure at The Mine

Post by mokganjetsi » Wed Nov 09, 2016 8:24 am

yikes!!

kudos for the practice to be on the chains and the bolt below that.

i would suggest staying off the routes at the Mine that have expansion bolts. or at least check when they were bolted.....

maybe it is a good time to start a flag system based on the type of bolt, age of bolts and the area - i.e. each route has a rating based on bolt safety as well. i think such a system is in use in thailand (?)

User avatar
Xenomorph
Posts: 378
Joined: Mon Feb 01, 2010 11:23 am
Real Name: Cormac Tooze
Location: Cape Town

Re: Bolt failure at The Mine

Post by Xenomorph » Wed Nov 09, 2016 8:25 am

Hi Chris,
Would you know if there is a stamped letter on the end of the shaft?

Cheers
Cormac

User avatar
Xenomorph
Posts: 378
Joined: Mon Feb 01, 2010 11:23 am
Real Name: Cormac Tooze
Location: Cape Town

Re: Bolt failure at The Mine

Post by Xenomorph » Wed Nov 09, 2016 8:36 am

mokganjetsi wrote:yikes!!

kudos for the practice to be on the chains and the bolt below that.

i would suggest staying off the routes at the Mine that have expansion bolts. or at least check when they were bolted.....

maybe it is a good time to start a flag system based on the type of bolt, age of bolts and the area - i.e. each route has a rating based on bolt safety as well. i think such a system is in use in thailand (?)
Route was bolted in 2003, so only 13 years old.
I'm not certain but I think this was one of the last routes not to be ARFed.
Trying to find out what type of bolt was used.
Most (90%) routes in Cape Peninsula are ARFed with Glue-ins, barring a few at Peers Cave and some routes 26+ elsewhere.

Cheers
Cormac

chrisb
Posts: 9
Joined: Mon Mar 07, 2016 10:04 pm
Real Name: Chris Barker

Re: Bolt failure at The Mine

Post by chrisb » Wed Nov 09, 2016 9:02 am

Xenomorph wrote:Hi Chris,
Would you know if there is a stamped letter on the end of the shaft?

Cheers
Cormac
Hi Cormac,
I'll check the make of the bolts when I go back there this Thursday.
Chris

Old Smelly
Posts: 551
Joined: Fri Nov 28, 2008 1:21 pm

Re: Bolt failure at The Mine

Post by Old Smelly » Wed Nov 09, 2016 9:30 am

Just an observation -

Funny that none of us actually like ending up on one bolt BUT very few people protest when the anchors are deliberately set up to load one bolt

YES I know this was argued back and forth and some contend that one bolt is plenty strong - they never fail right!

BUT see how when it comes down to it all two equalised anchors do give more confidence and have the added value that if one fails there is very little shockload! With no real downside.

I rest my case.
Really, its not that bad...I think it's my shoes...

hendriks
Posts: 93
Joined: Mon May 25, 2009 10:29 pm

Re: Bolt failure at The Mine

Post by hendriks » Wed Nov 09, 2016 9:32 am

I would strongly recommend that people only back climb when they need to, i.e. Only when it is not safe to top rope. Then you always have a long line of bolts. Back climbing is in my opinion a very dangerous thing to do as often you hear about someone completely unclipping themselves.

mokganjetsi
Posts: 1549
Joined: Fri Dec 15, 2006 12:32 pm
Real Name: Willem Boshoff
Location: Cape Town

Re: Bolt failure at The Mine

Post by mokganjetsi » Wed Nov 09, 2016 9:36 am

Xenomorph wrote:Most (90%) routes in Cape Peninsula are ARFed with Glue-ins, barring a few at Peers Cave and some routes 26+ elsewhere.
i have some concerns re some routes at montagu, hellfire etc. a lot of them bolted in the early & mid-90's. it would be useful to develop a safety benchmark for bolt type, age & area. e.g. for expansion bolts: the Mine 15-years; Montagu 20-years etc. not sure what those numbers should be though.

i have been supplementing some older bolts (where i can) with trad placements

User avatar
Wes
Posts: 314
Joined: Sat Jan 08, 2011 10:25 pm
Real Name: Wesley

Re: Bolt failure at The Mine

Post by Wes » Wed Nov 09, 2016 9:40 am

Hey Guys,

Just got confirmation from Chris that it was actually the bolt the sheared off. Leaving about 3mm protruding from the rock.

Imaging showing the hanger:

Image curtsey of Chris:
646c44e7-a067-47ef-be31-009ad64fdea9.jpg
646c44e7-a067-47ef-be31-009ad64fdea9.jpg (138.19 KiB) Viewed 1555 times
Last edited by Wes on Wed Nov 09, 2016 10:54 am, edited 3 times in total.
Reason: Incorrect photo credit.

chrisb
Posts: 9
Joined: Mon Mar 07, 2016 10:04 pm
Real Name: Chris Barker

Re: Bolt failure at The Mine

Post by chrisb » Wed Nov 09, 2016 9:53 am

Wes wrote:Hey Guys,

Just got confirmation from Chris that it was actually the bolt the sheared off. Leaving about 3mm protruding from the rock.

Imaging showing the hanger:

Image curtsey of Jayson:
646c44e7-a067-47ef-be31-009ad64fdea9.jpg
Hi Wes,

That's the pic I took of the hangar/oval. The bolt snapped off with the nut still on leaving about 3 millimetres of jagged, rusty metal protruding from the rock.

User avatar
Xenomorph
Posts: 378
Joined: Mon Feb 01, 2010 11:23 am
Real Name: Cormac Tooze
Location: Cape Town

Re: Bolt failure at The Mine

Post by Xenomorph » Wed Nov 09, 2016 10:33 am

The bolts which have been failing are the ones with-out a letter designated on the head.
Not sure if that is the case with this route .
Attached is an example of a correct Hilti/ Fisher bolt.
FYI: Each letter corresponds to the length of the bolt.

Cheers
Cormac
Attachments
Bolt with Letter.JPG
Bolt with Letter.JPG (25.57 KiB) Viewed 1530 times

Keith
Posts: 90
Joined: Tue Apr 25, 2006 9:50 am

Re: Bolt failure at The Mine

Post by Keith » Wed Nov 09, 2016 1:19 pm

Totally disagree old smelly

Look up "common mode failure"

(and "American death triangle")

User avatar
Nic Le Maitre
Posts: 1189
Joined: Mon Apr 02, 2007 9:40 am
Real Name: Nic Le Maitre
Location: Stellenbosch

Re: Bolt failure at The Mine

Post by Nic Le Maitre » Thu Nov 10, 2016 8:37 am

Here's a thought:

We have no idea what configuration the bolts at the top of this route were in. Until we do, any speculation is pointless as the facts as they stand can be argued either way.

What we do know is that SCC is bad, some of the routes at the Mine may have suffered from it. Make sure you only climb routes on the new ARF bolts.
Happy climbing
Nic

Old Smelly
Posts: 551
Joined: Fri Nov 28, 2008 1:21 pm

Re: Bolt failure at The Mine

Post by Old Smelly » Thu Nov 10, 2016 11:12 am

Keith it would be idiotic to imply that equalised anchors and the American Death Triangle have any real context to each other!
American Death Triangle.gif
American Death Triangle.gif (14.55 KiB) Viewed 1283 times
How an anchor is rigged is up to the person who attaches to it and has nothing to do with the position of the anchor points - in fact by just making it impossible to equalise with 2 similar length quickdraws, you are probably more likely to have people who create an ADC - so I do not know if you have a point at all or whether you grasp that an ADC can happen wherever there are two anchors.

Lets looks back at the three legged cow and point out that shared load will extend the life of each anchor way more then if you load one until it fails and then load the next one. That is logical. Shared loads are logical, which is why my four legged table (or cow) is able to cope better than your one legged table or 3 legged cow. Let's just say that most people prefer to be on two anchors than one.

How about you try this- climb really high up a big wall and then place one piece of pro and suspend all your gear and yourself off it. Then go to sleep for the night - and tell yourself it's only a static load and go to sleep (after reading a long and tedious explanation on common mode failures - and if that can't get you to go to sleep then not much will) Surely by that distorted logic and your implicit faith in it you will sleep soundly...
Really, its not that bad...I think it's my shoes...

hendriks
Posts: 93
Joined: Mon May 25, 2009 10:29 pm

Re: Bolt failure at The Mine

Post by hendriks » Thu Nov 10, 2016 11:52 am

How about we take this "How should we bolt top anchors debate" here: viewtopic.php?f=13&t=13271

Then we can keep this thread on track :thumleft:

User avatar
Nic Le Maitre
Posts: 1189
Joined: Mon Apr 02, 2007 9:40 am
Real Name: Nic Le Maitre
Location: Stellenbosch

Re: Bolt failure at The Mine

Post by Nic Le Maitre » Thu Nov 10, 2016 11:58 am

Fact: We don't know which configuration the bolts were in

Fact: SCC is not caused by climbers hanging on the bolts or falling on them either. It is caused by chemical weathering of the steel structure along weak points in the grain structure of the metal.

Pointless speculation in the absence of ANY evidence is just that, pointless.
Happy climbing
Nic

Marshall1
Posts: 744
Joined: Fri Jun 27, 2008 8:38 am
Real Name: Derek Marshall
Location: Port Elizabeth

Re: Bolt failure at The Mine

Post by Marshall1 » Thu Nov 10, 2016 4:54 pm

Donald Trump = importance of fact checking.

Stress is an element of Stress Corrosion Cracking. Falling on to a bolt would be a stress factor.

https://en.wikipedia.org/wiki/Stress_corrosion_cracking

User avatar
Nic Le Maitre
Posts: 1189
Joined: Mon Apr 02, 2007 9:40 am
Real Name: Nic Le Maitre
Location: Stellenbosch

Re: Bolt failure at The Mine

Post by Nic Le Maitre » Thu Nov 10, 2016 5:05 pm

The SCC in the Cape is as a result of using a bad batch of expansion bolts and the constant tension on the bolt produced by the nut. This is why the ARF are rebolting with P-bolts that glue in.
Happy climbing
Nic

User avatar
henkg
Posts: 386
Joined: Fri Sep 25, 2009 11:21 am
Real Name: Henk Grobler

Re: Bolt failure at The Mine

Post by henkg » Thu Nov 10, 2016 5:54 pm

Marshall1 wrote:Donald Trump = importance of fact checking.

Stress is an element of Stress Corrosion Cracking. Falling on to a bolt would be a stress factor.

https://en.wikipedia.org/wiki/Stress_corrosion_cracking
Can you prove that climber induced "stress" is of sufficient duration and magnitude to meaningfully contribute to SCC? It should only be a factor to an already weakened anchor.
You may still be here tomorrow, but your dreams may not. Cat Stevens

User avatar
Scott
Posts: 75
Joined: Tue Nov 01, 2005 3:06 pm
Real Name: Scott Miller

Re: Bolt failure at The Mine

Post by Scott » Sun Nov 13, 2016 8:04 pm

Glad No one was hurt. All bolts placed then were whatever the MCSA was recommending. Purchased from Dave Davies at MMO. All bolts Ive ever placed in RSA have been whatever the MCSA was recommending at the time purchased either at MMO, City Rock or Fischer/UPat.

Most of those routes were put up in the same time frame so whatever hasn't been ARF'ed should be avoided I would assume.

Cheers
Scott

User avatar
Xenomorph
Posts: 378
Joined: Mon Feb 01, 2010 11:23 am
Real Name: Cormac Tooze
Location: Cape Town

Re: Bolt failure at The Mine

Post by Xenomorph » Mon Feb 27, 2017 9:28 pm

Route has now been ARF'd

Thanks, Mary, Ryan and Brian

Cheers
Cormac
Last edited by Xenomorph on Tue Feb 28, 2017 5:47 am, edited 1 time in total.

KaiPF
Posts: 36
Joined: Mon Dec 01, 2008 5:13 pm

Re: Bolt failure at The Mine

Post by KaiPF » Mon Feb 27, 2017 11:57 pm

Great stuff ARFers! Appreciate the hard work!

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest